There are many different landscaping ideas that can be implemented in order to beautify an otherwise mundane looking yard or patio area. One such way is installing a stream, pond, or water display. Using a pondless waterfall kit, you can create a beautiful scene that includes the sounds of natural water flow. The process takes some planning and time but is well worth the effort.
First, you need to decide on the area you want to place it. By figuring out the design ahead of time, you can mark out where to dig and where the stream will go. Once you have any underground lines marked by the utilities, use spray paint to map out where the reservoir will be and the path of the stream back to the spillway.
Start digging out the reservoir and move the dirt to the area that the spillway will sit. As you dig, the reservoir should be square or round and about two feet deep. In the middle of it, you need to dig another 6 to 8 inches to place the vault that will hold the pump. Using a vault keeps the pump from getting damaged and allows it to sit at the lowest point of the reservoir.
Install the liner next. This is important because you do not want to lose water by having it enter the soil. There are a couple of different types of the liner that you should use. At least one layer should be a thick rubber liner. Having multiple layers will keep it from getting pierced or torn and allowing water to flow out of the reservoir.
Attach the flex hose to the pump and run it uphill. If you want to dig a trench to bury the hose, you may at this point, but you should have enough dirt to bury it without a trench. It is best to keep it uncovered until the last step. This hose will be hooked up to the spillway to create the water flow.
Use bigger gravel in the bottom and begin filling in the reservoir. Dirt and sand can wash away and become saturated. The rocks will hold everything in place. As you build it up, begin adding larger rocks, even boulder size, for decoration. You will begin placing them along the path of the stream up to the spillway.
The larger boulders can be used in various points to create additional spillways and paths. When these are in place, begin filling in areas with different types of rocks and gravel for decorative purposes and to create a natural stream. Before you're done, run water through the system to see where the water path will go and adjust the rocks and liner as needed.
Once things are set, finish filling in the stream and cover the flexible tubing. Using the leftover dirt, you can cover the tubing and any liner that is exposed outside of the water flow. Dirt will wash away, so anyplace the water flows should be covered with rocks and decorative gravel. After this is done, you can begin putting in plants, flowers, leaves, or other decorative natural items to help complete the scene.
First, you need to decide on the area you want to place it. By figuring out the design ahead of time, you can mark out where to dig and where the stream will go. Once you have any underground lines marked by the utilities, use spray paint to map out where the reservoir will be and the path of the stream back to the spillway.
Start digging out the reservoir and move the dirt to the area that the spillway will sit. As you dig, the reservoir should be square or round and about two feet deep. In the middle of it, you need to dig another 6 to 8 inches to place the vault that will hold the pump. Using a vault keeps the pump from getting damaged and allows it to sit at the lowest point of the reservoir.
Install the liner next. This is important because you do not want to lose water by having it enter the soil. There are a couple of different types of the liner that you should use. At least one layer should be a thick rubber liner. Having multiple layers will keep it from getting pierced or torn and allowing water to flow out of the reservoir.
Attach the flex hose to the pump and run it uphill. If you want to dig a trench to bury the hose, you may at this point, but you should have enough dirt to bury it without a trench. It is best to keep it uncovered until the last step. This hose will be hooked up to the spillway to create the water flow.
Use bigger gravel in the bottom and begin filling in the reservoir. Dirt and sand can wash away and become saturated. The rocks will hold everything in place. As you build it up, begin adding larger rocks, even boulder size, for decoration. You will begin placing them along the path of the stream up to the spillway.
The larger boulders can be used in various points to create additional spillways and paths. When these are in place, begin filling in areas with different types of rocks and gravel for decorative purposes and to create a natural stream. Before you're done, run water through the system to see where the water path will go and adjust the rocks and liner as needed.
Once things are set, finish filling in the stream and cover the flexible tubing. Using the leftover dirt, you can cover the tubing and any liner that is exposed outside of the water flow. Dirt will wash away, so anyplace the water flows should be covered with rocks and decorative gravel. After this is done, you can begin putting in plants, flowers, leaves, or other decorative natural items to help complete the scene.
About the Author:
Get a summary of the factors to consider when choosing a pondless waterfall kit supplier and more information about a reputable supplier at http://www.boulderfountain.com/pondless-waterfall.html now.